Mbrp S6116SLM Bedienungsanleitung PDF herunterladen

Removal of Stock System:

1. Apply a penetrating lubricant liberally to all exhaust fasteners, hangers and rubber insulators.

2. Remove the exhaust system from the rubber insulators and remove all of the clamps from the system.

3. Separate the slip joint behind the muffler and remove the tail pipe. Next, separate the slip joint connecting the down pipe and the extension

pipe to remove the muffler and extension pipe. Finally loosen the band clamp connecting the down pipe to the turbo and remove the down

pipe. Do not discard the band clamp as it is required for the installation.

4. Remove the OEM down pipe hanger bracket from the bellhousing. Do not discard these parts as they are required for the installation.

Installation of MBRP Inc. Performance Exhaust:

1. Slide the OEM down pipe hanger bracket onto the Down Pipe hanger. Install the Down Pipe in the same position as the stock down pipe

by reattaching the hanger bracket to the bellhousing and then attaching the flared end to the turbo using the stock band clamp. Do not fully

tighten until all components are in place.

2. Install the Extension Pipe 42” onto the Down Pipe and then the Extension Pipe 26” onto the Extension Pipe 42”. The combination of the

both Extension Pipes provides the required length to fit a Quad Cab Long Bed truck or Mega Cab. These pipes will have to be cut to fit all

other vehicles. Installation Tip: Temporarily install the Muffler Delete and Tail Pipe using the factory rubber insulators and the Hanger

Clamp. Measure from the Muffler Delete to the Mid Pipe to determine the length required. Cut the pipe to the required length.

3. Install the Muffler Delete over the Extension Pipe and the Hanger Clamps into OEM rubber hangers refer to the illustration.

4. Install the Tail Pipe from the rear of the truck, over the axle and attach to the outlet of the Muffler Delete. Install the hanger on the Tail

Pipe to the existing OEM rubber hanger.

5. Install the provided Clamps around the pipes where required. Adjust the Tail Pipe and check along the whole length of the exhaust system

to ensure there is adequate clearance around the fuel and brake lines or any wiring. If any interference is detected relocate or adjust.

6. Start at the front of the exhaust system and begin tightening all connections. Recheck for interference after tightening and adjust if

required.

PLEASE NOTE: This system is designed for off

PLEASE NOTE: This system is designed for offPLEASE NOTE: This system is designed for off

PLEASE NOTE: This system is designed for off-

-road use only. If highway operation is intended please consult your local or state authority

road use only. If highway operation is intended please consult your local or state authority road use only. If highway operation is intended please consult your local or state authority

road use only. If highway operation is intended please consult your local or state authority

for more information

for more informationfor more information

for more information.

Congratulations! You are ready to begin experiencing the improved performance and driving excitement of your MBRP Inc. performance

exhaust system. We know you will enjoy your purchase.

Removal of Stock System: 1

Inhaltsverzeichnis

Seite 1 - Removal of Stock System:

Removal of Stock System: 1. Apply a penetrating lubricant liberally to all exhaust fasteners, hangers and rubber insulators. 2. Remove the exhaust

Verwandte Modelle: S6116PLM

Kommentare zu diesen Handbüchern

Keine Kommentare

Mbrp S6116SLM Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Mbrp S6116SLM herunter. MBRP S6116SLM User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: S6116PLM

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Mbrp S6116SLM