Mbrp S6212SLM Bedienungsanleitung PDF herunterladen

Removal of Stock System:

1. Loosen the nut on the band clamp located behind the catalytic converter using a 15mm wrench or socket.

2. If a hoist is being used for the installation, the original exhaust system can be removed in one piece by removing the passenger side shock. If a hoist is not

being used the tail pipe must be cut behind the muffler to be removed.

3. Remove the muffler and tail pipe from the OEM rubber hangers and separate the stock exhaust at the slip joint located behind the catalytic converter and

remove the muffler and tail pipe from under the truck. Re-install the passenger side shock.

4. Remove the catalytic converter by removing the two nuts holding the inlet flange together using a 15mm wrench or socket.

5. Remove the down pipe from the turbo by removing the band clamp using an 11mm socket. Retain the band clamp for the installation of the Down

Pipe. Cut the down pipe in front of the transmission cross member to remove. (Note: The stock down pipe can be removed in one piece by removing the

transmission cross member. It is recommended that this only be done by qualified, trained professionals using tools and equipment designed to safely

carry out this procedure.)

Installation of MBRP Inc. Performance Exhaust:

1. Install the Down Pipe in the same position as the stock down pipe and attach the flared end to the turbo using the stock band clamp. Do not fully tighten

until all components are in place.

2. Attach the Mid Pipe to the Down Pipe using a 3 ½” Clamp and place the hanger into the factory rubber insulator located on the frame.

3. Attach the 42" Extension Pipe to the Mid Pipe. For Extended Cab Short Bed vehicles this is the only Extension Pipe required. For Crew Cab Long Bed

vehicles you will require the full length of both the 32" Extension Pipe and the 42" Extension Pipe. For Extended Cab Long Bed and Crew Cab Short Bed

vehicles the 32" Extension Pipe will have to be cut. For Extended Cab Long Bed vehicles attach the two extension pipes and cut the 32" Extension Pipe to

a combined, attached length of 57 1/4". For Crew Cab Short Bed vehicles attach the two extension pipes and cut the 32" Extension Pipe to a combined,

attached length of 55 1/4".

4. Install the Muffler Delete over the Extension Pipe. Install the “T” Hanger Clamp into the two OEM rubber hangers located above the outlet of the Muffler

Delete .

5. Install the Over Axle Pipe from the rear of the truck, over the axle and attach to the outlet of the Muffler Delete. Attach the Tail Pipe to the Over Axle

Pipe. Install the tail pipe hanger into the OEM hanger to complete.

6. Install the provided Clamps around the pipes where required. Starting at the front of the exhaust, add and tighten all clamps. Adjust the Tail Pipe and

check along the whole length of the exhaust system to ensure that there is adequate clearance around the fuel and brake lines or any wiring. If any

interference is detected relocate or adjust.

Congratulations! You are ready to begin experiencing the improved performance and driving pleasure of your MBRP Inc.

performance exhaust system. We know you will enjoy your purchase.

Inhaltsverzeichnis

Seite 1 -

Removal of Stock System: 1. Loosen the nut on the band clamp located behind the catalytic converter using a 15mm wrench or socket. 2. If a ho

Verwandte Modelle: S6212PLM

Kommentare zu diesen Handbüchern

Keine Kommentare

Mbrp S6212SLM Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Mbrp S6212SLM herunter. MBRP S6212SLM User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: S6212PLM

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Mbrp S6212SLM